Tycon Power Solar MPPT Battery Charging Controller , Auto Voltage, 12/24/36/48V, 60A Solar
|Rated Battery Voltage||12/24/36/48V (Auto-Detect), 70V Max|
|Rated Solar Current||60A Max|
|Max Solar Panel Size||12V Battery = 800W 24V Battery = 1600W 36V Battery = 2400W 48V Battery = 3200W|
|Rated Load Current||20A Max|
|Maximum Capacitive Load||10,000uF|
|Max Solar Input Voltage||150V (25C) ; 145V (-25C)|
|Max Power Point Range||+2VDC to 120VDC Battery Volts|
|Conversion Efficiency||98% Typ|
|MPPT Tracking Efficiency||>99%|
|Communication Port||RS232 (for TP-SC-BT1 only) RS485 (for controller sync)|
|Max Wire Size||7 AWG|
|Voltage / Current Accuracy||+/-2%|
|Operating Temp||-35°C to 55°C (-31°F to 131°F)|
Tycon Power TP-SC48-60-MPPT
Solar MPPT Battery Charging Controller , Auto Voltage, 12/24/36/48V, 60A Solar, 20A Load
The Tycon Solar™ TP-SC48-60-MPPT solar controllers are MPPT (Maximum Power Point Tracking) temperature compensated battery charging controllers. The 9ft battery temperature probe cable is included. The controllers are auto-ranging to accommodate 12V, 24V, 36V and 48V battery systems. There is a separate battery voltage input so that the controller can get very accurate readings of battery voltage. This removes voltage fluctuations seen because of large currents going through the battery cables.
They are designed to charge Flooded, AGM, GEL or Lithium batteries. They also have a USER setting for customizable battery charge settings. They have an integral LCD display that shows Battery Voltage, Battery Capacity, Charging Capacity, Battery Temperature, Load Current and Solar Current.
There is an RS232 interface to connect to the Tycon #TP-SC-BT1 Bluetooth adapter (not included). Using this configuration and the available Android or IOS mobile app, the solar controller can be monitored and controlled from a distance. There is also an RS485 port which allows sync of multiple controllers connected in parallel. A 36in RS485 interface cable is included.
They have multiple load operating modes which can be set through the buttons on the controller.
The load output has a soft start feature so it can smoothly and reliably power up high capacitance loads up to 20A. There is a convenient On/Off button to disconnect load power when the unit is operated in the default mode (15). They have full electronic protections for short circuit, reverse current, over-power, over-voltage, over-charge, over-discharge and over-temperature. The built-in over-discharge protection and low self consumption ensures the battery is not over-discharged, which greatly increases the life of the batteries. All protections are auto-recovery.
The units are protected against lightning strikes with TVS diode protection. They operate over a wide industrial temperature range. Electronics are conformal coated for environmental protection.
An automatic battery equalization charge automatically engages once every 30days (Programmable). The equalization charge helps to balance the batteries in an array and reduce the possibility of battery sulfation.
Connections are via 6 screw terminals for wire size up to 7AWG. The controllers are internally fused for protection, but we recommend always using an external 60A fuse between the controller and the battery. There are four screw holes for wall mounting. In addition, there are two DIN Rail brackets for DIN Rail mounting included.
- MPPT Temperature Compensated Charging
- Fully Automatic Operation
- LCD Displays: Battery Volts, Battery Temp, Battery Level, Load Current and Solar Current
- Autoranging 12/24/36/48V Battery Arrays
- Multimode Load Operation – 5 selectable modes
- Soft Start Load Output to Power High Capacitive Loads
- Automatic 30day Battery Equalization
- Conformal Coated Electronics for Environmental Protection
- TVS lightning protection, Industrial Temperature Range
- Low self consumption <1W