• Home
  • Tycon Power High Power 5 port Gigabit 802.3at PoE Switch with 12-36V DC Input

Tycon Power High Power 5 port Gigabit 802.3at PoE Switch with 12-36V DC Input

(0) No Reviews yet
$249.95

Specifications TP-SW5G-24HP

Ethernet Standard IEEE802.3/IEEE802.3u
Ports 1 data/PoE input and 4 data/PoE, automatic crossover and polarity
Transmission Speed1000Mbps / 100 Mbps /10 Mbps Auto-negotiation
Switch Technology Store and Forward
Protocol CSMA/CD
Flow Control IEEE802.3x(full-duplex), Back Pressure(half-duplex)
Data Transmission Rate 1488000pps for 1000baseT, 148800pps for 100baseT, 14880pps for 10baseT
Address Table 1K MAC, self-learning
Connections Shielded RJ45
POE Output Ports Port 1-4, auto power management Pin assignment: TX(1,2), RX(3,6), V+(4,5), V-(7,8)
Maximum POE Power Up to 35W per port; max 70W Total per switch HP with 24V Input 140W Total HP with 12V Input 70W Total
POE Auto Detection IEEE 802.3af, 802.3at
POE Protection Over Temperature, Over Current, Over/Under Voltage
Data Surge Protection IEC61000-4-2 (ESD) ±15kV (air), ±8kV (contact) IEC61000-4-4 (EFT) 40A (5/50ns) IEC61000-4-5 (Lightning) 20A (8/20μs)
LED’s Link (Green On), Activity (Green Blinking ); PoE Detect (Yellow On), PoE Detect Error (Yellow Blinking) Power On (Green On), Power On Alarm (Red On)
DC Power Input 24VDC (12V to 36V), Dual DC Inputs, Reverse Polarity Protected. Also Accepts PoE power input on Port 5
Self Consumption < 4 Watts
Operating Temp -40 to +70°C (-40 to 158°F)
Operating Humidity (RH) 5% - 90% (non condensing)
Storage Temperature -55 to +85°C (-67 to +185°F)
Dimensions (LxWxH) (3.5 x 4.6 x 1.6”) 159 x 118 x 40mm (6.3 x 4.6 x 1.6”) (HP version has metal housing)

Tycon Power TP-SW5G-24HP

High Power 5 port Gigabit 802.3af/at PoE Switch with 12-36V DC Input

The TP-SW5G-24HP Power Over Ethernet (PoE) 10/100/1000Mb switch offered by Tycon Power Systems is a fully automatic high speed 5 port Ethernet switch with up to 35 Watts of PoE power per port. It complies with the IEEE802.3af/at specifications for valid PoE device detection. It accepts 12-36VDC power on the wire terminal input and supplies power on 4 ports with 802.3at PoE output. Maximum output power for all ports is 140W with 24V input and 70W with 12V input.

The unit supplies power to the remote device on the unused Ethernet pins 4,5(V+) and 7,8(V-). The Ethernet spec supports distances up to 100m (328 feet) between the PoE switch and the remote device.

The switch accepts DC power from a user supplied 10-36VDC power source. There are 2 power inputs for attachment of primary and backup power sources.

The switch also accepts PoE power via the 802.3af/at uplink port (90W Max). Metal Housing, No Fan

Ratings & Reviews

No reviews available

Be the first to Write a Review