Data Alliance N-male To RP-SMA male Cable 30-inch Outdoor / Indoor Double-Shielded

Data Alliance Nm30iRSm

N-male To RP-SMA male Cable 30-inch Outdoor / Indoor Double-Shielded

Antenna Cable with RP-SMA connector on one end and an N-male connector on the other end.

Features:

• This cable is rated for outdoor use and is also suitable for indoor use.
• The length refers to the length of the cable between the connectors (not including the connectors).
• Allows interconnection of devices with RP-SMA female and N-female interfaces: Antennas, antenna cables and wireless devices.
• For coaxial extension (for better antenna positioning), coaxial interface conversion, coax retrofit applications.
Data Alliance's high-quality soldered terminations of RP-SMA and Type-
• N connectors with soldering provide a low-loss connection with discontinuities kept to a minimum.

Compatibility with wireless applications: Our RP-SMA-male to N-male cable' range of frequency band compatibility (from 0GHz to 18GHz), consistently low broadband VSWR, and impedance matching to 50 Ohm gear, makes them compatible and compliant for all the following applications:

• All WiFi standards: 2.4GHz and 5GHz applications: 802.11AC, 802.11N, 802.11G, 802.11B, 802.11A
• Cellular Wireless LTE / 4G, GSM / 3G WiMax, 5G: Data and voice applications
• IoT wireless, automation & Machine to Machine (M2M): Bluetooth, ZigBee, RFID, LoRa, LTE-m, NB-IoT.
• Compatible with all Helium miners used in North America, including Bobcat miners, Sensecap miners and all other Helium LongFi miners, as are all of our antenna cables and adapters with RP-SMA-male connectors.

Cable is double-shielded for low signal-loss, and is very flexible/easily bendable. Coaxial cable type is similar to LMR-100 but better quality than LMR100: Coax with black jacket has the same or better signal-loss-per-meter and flexibility as LMR100, and less attenuation (signal loss) than RG174. The double-shielding is a major factor in the higher quality of this cable, translates into lower loss/better performance. Cable is equivalent to LMR-100 in thickness.

N-male Connector Characteristics and Details

• The N-male connector has an interior rubber O-ring, which provides a water-tight seal.
• N is nickel-plated brass, which is the best metals composition for rust-proof / corrosion proof / weatherproofing for long-term outdoor exposure.
• Our N connectors provide a consistent performance from 900MHz to 12.5 GHz.
• The N-male connector is knurled.
• N-Female diameter is 0.620-inch (1.57 cm). N-male inside diameter is 0.620-inch (1.57 cm)
• N-connector gender is counter-intuitive: Click here for details.
• N-Type connectors are the largest of the RF connector types, and are usually found on large antennas, especially for outdoor use.
• Our N-Type connectors feature threaded coupling mechanisms and are fully interchangeable with N-Type connectors made to the MIL-C-39012 specification. These connectors are used in all systems where excellent RF and mechanical performance is critical.

N materials composition:

• Connector Body: Nickel-Plated Brass: The most corrosion-resistant of all plated brass alloys (better than gold-plated).
• Center Contact: Beryllium Copper, Gold Plated
• Crimp Ferrule: Copper, Nickel Plated
• Insulators: PTFE

RP-SMA Connector Characteristics and Details

RP-SMA male and female diameter:

• RP-SMA male inside diameter is 5/16" (7.9375mm) (the inside diameter where the threads are).
• RP-SMA female outside diameter is 5/16" (7.9375mm): Accommodates a hex nut (bulkhead nut) with 5/16" nominal outer diameter

RP-SMA Gender Determination: Key Points

• RP-SMA gender is counter-intuitive: Please observe picture & note it is correct.
• The gender is referring to the pins inside--not the threads. RP-SMA male has threads on inside.
• RP-SMA male has a socket inside rather than a pin, as you might expect, because the RP stands for "Reverse Polarity." The socket/pin configuration is female when it appears to be male, and vice versa.

RP-SMA-Connector Materials Composition:

• Connector Body: Gold Plated Brass
• Center Contact: Beryllium Copper, Gold Plated
• Crimp Ferrule: Copper, Nickel Plated
• Insulators: PTFE
• Precision machined for low loss in ISO 9001 facilities

Other RP-SMA Characteristics and Key Points

• RP-SMA-male is also called "plug" and SMA female connector is also called "jack"
• We offer an RP-SMA wrench to assist in installing antennas, cables and adapters with RP-SMA or SMA connector(s).
• RP-SMA-male connector fits items that have an SMA-female connector.
• RP-SMA is a round screw-type connector, with medium-sized, threaded coupling connectors that are rated for frequencies from the lowest (DC) up to 18GHz.
• RP-SMA connectors are not compatible with the common, commercially available Type F coaxial connector. Type F connectors look similar but are of slightly different size and will not pair with RP-SMA or SMA connectors without an adapter.

RoHS and REACH compliant: All of our antenna cables and adapters are compliant with RoHS 3 and REACH restrictions on heavy metals and other toxins.